Fix Your Roof Ice Problems with Heat Tape

When trying to find ways to keep ice from forming on a roof, on-line searches to sites like Red Deer eavestrough reveal advice about a heat cable system that eradicates icicles and ice dam formation economically and safely; found on many buildings positioned in snow-covered places and can be purchased in many hardware stores. This product is a sort of “heat cassette” that can be sliced and spliced to fit the layout of any roof or gutter for snow-melting and de icing purposes.

A roofing system with inadequate venting during wintry weather may cause ice dams that form in the edge of a roof, hindering ice that is melting from flowing down the gutters and into downspouts for proper drainage. Eventually, melted snow water will stagnate and penetrate shingles, sheathing, and decking. A powerful economic, and long-term option to stop this occurrence from occurring would be to install heat tape on gutters, roofs, valleys or even on downspouts.

The primary purpose of heat tape is to keep or increase the surface temperature of issue regions to an above-freezing temperature. Placement of the merchandise on the lower edge of the roof or in gutters, valleys, and downspouts can help keep the eaves free from snow or ice build up. It is very important to notice that the structure will likely be entirely free from ice or snow; nonetheless, it does create a clear path for the melted snow and into the drain pipes.

Types and Designs
This merchandise can be bought in fixed durations, typically ranging from two to twenty feet determined by the design. It’s also available in 120 and 240 volt variants with power options which range from 50 to 3,135 watts. It can also be purchased in various widths ranging from one-half to one and three -quarter inch. Moreover, the apparatus must have a temperature control to match changing weather conditions. Some commercial building owners prefer to have a thermostat installed so that when the temperature drops to a particular level, the system will activate.

Setup Procedure
It’s quite easy install this device to stop serious damage to a building. Before beginning installation, check for absolutely any existing heating system products in the roof. This really is an important security test since many fires are the result of previously wrongly installed de-icing cables as reported by United States Consumer Products Safety Commission (USCPSC). As a security precaution, always read the manufacturer’s guidelines as an important reminder. Other significant installation hints contain:

* Dry Roof – Positioning should only be done when the roofing is totally dry. It’s a good idea to plan the project ahead of time and program installment during the fall before winter weather hits.

* Inspect Kit – Open the kit and assess all included materials. It commonly includes hardware for complete installation, control box, cable, and a thermostat.

* Mount Control Box – Put the control box in a place that is accessible, suitable, and close to an electrical socket, preferably underneath a soffit. The system ought to be grounded to prevent any accidental electrical shock.

* Install Roof Tape– After attaching the management box, install the tape by means of a zigzag pattern, being certain to cover an area two feet from the roof line. The conventional kit usually contains clips which can be used to hook onto roof edges. Put the tape and sensor wires roof edges, on the valleys, to be able to cover those areas prone to ice dam formation eaves troughs, and drainpipes.

* Seek Help – If doubtful regarding the right installation procedure, call an expert commercial roofing company to finish the job before the snow begins to fall.

Security Measures
Safety should always take precedence in any job that requires electricity. The United States Consumer Product Safety Commission (CPSC) recommends the following safety tips when buying and installing heat tape:

* Replacement – Heating cables that are not certified for longer use and over three years old ought to be replaced with new ones to meet safety standards.

* Appropriate Stopper – Make sure a three-pronged plug is used and correctly grounded.

* Use GFCI – Always use a ground fault circuit interrupter (GFCI).

* No Overlap – Unless enabled by producer avoid overlapping the tape over itself.

* Correct Merchandise – Use only products created for roofing applications.

* End-Cap – Always seal the end-cover and keep it away from the earth to prevent moisture.

* Thermostat – If a thermostat is contained, follow the manufacturer recommendations about the positioning that is correct.

* Care – On any existing heat tape, check for signs of deterioration (discoloration, charring, reductions, and breaks).

Understanding about heat tape is necessary to decrease the risk of a roof escape forming during winter conditions. With the aid of a thermostat, heat tape can stop the formation of ice on roof edges. This endeavor can be handle yet, it’s often better to seek aid from a roofing business because for safety reasons. So don’t let a roof ice up – use heat tape to melt down any troubles away!